河南渑池地区铝土矿工艺矿物学及锂的赋存状态研究

通过河南省渑池地区含锂铝土矿(岩)层工艺矿物学分析,查明铝土矿的物质组成、嵌布特征、伴生锂分布特征和赋存状态,为矿产综合利用提供理论依据。结果显示:该铝土矿Al2O3含量为54.8%,铝硅比值(A/S)为2.6,铝土矿层和粘土岩层中Li2O含量均高于伴生锂边界品位,粘土岩中锂更为富集；矿物组成除一水硬铝石之外,主要是以集合体形态产出的粘土矿物。采用稀酸解析、选矿测试和电子探针分析锂的赋存状态,查明矿石中锂主要是以类质同象置换形式赋存在伊利石和高岭石等粘土矿物中；选矿富锂尾矿中Li2O可富集到0.57%左右,是锂综合回收利用的重点研究对象。      

Effects of the film thickness and poling electric field on photovoltaic performances of (Pb,La)(Zr,Ti)O3 ferroelectric thin film-based devices

The ferroelectric photovoltaic (FPV) effect obtained in inorganic perovskite ferroelectric materials has received much attention because of its large potential in preparing FPV devices with superior stability, high open-circuit voltage (V_oc) and large short-circuit current density (J_sc). In order to obtain suitable thickness for the ferroelectric thin film as light absorption layer, in which, the sunlight can be fully absorbed and the photo-generated electrons and holes are recombined as few as possible, we prepare Pb_0.93La_0.07(Zr_0.6Ti_0.4)_0.9825O₃ (PLZT) ferroelectric thin films with different layer numbers by the sol-gel method and based on these thin films, obtain FPV devices with FTO/PLZT/Au structure. By measuring photovoltaic properties, it is found that the device with 4 layer-PLZT thin film (~300 nm thickness) exhibits the largest V_oc and J_sc and the photovoltaic effect obviously depends on the value and direction of the poling electric field. When the device is applied a negative poling electric field, both the V_oc and J_sc are significantly higher than those of the device applied the positive poling electric field, due to the depolarization field resulting from the remnant polarization in the same direction with the built-in electric field induced by the Schottky barrier, and the higher the negative poling electric field, the larger the V_oc and J_sc. At a -333 kV/cm poling electric field, the FPV device exhibits the most superior photovoltaic properties with a V_oc of as high as 0.73 V and J_sc of as large as 2.11 μA/cm². This work opens a new way for developing ferroelectric photovoltaic devices with good properties.     

Ultrasonic tomographic velocimeter for visualization of axial flow fields in pipes

An ultrasonic tomographic velocimeter to provide quantitative images of axial flow fields in pipes is developed and presented in this work. To detect the flow in various directions and positions, a novel transducer configuration strategy is proposed. All-in-one transducers are mounted in two sectional planes of the pipe. In each plane, N transducers are equally spaced along the circumference. Overlapped propagation paths are introduced by the configuration strategy, and the influence of the vortex flow can be eliminated theoretically by averaging the line velocities of the overlapped paths. To achieve a fast detection speed, the projection data is collected via an electrical scan in a fan-beam mode. After rearrangement and interpolation of the projection data, the parallel beam filtered back projection (FBP) algorithm is implemented to reconstruct the axial flow field. Numerical simulations with the theoretical velocity profiles were performed. The compensation method for the vortex flow is proved to be effective and necessary, and the number of transducers required for reconstruction of common flow profiles was estimated. Accordingly, an ultrasonic tomographic velocimeter consisting of 2×12 transducers was fabricated. Experiments were conducted in the straight pipe and downstream of a single bend pipe and compared with the computational fluid dynamics (CFD) simulation results. As demonstrated, the ultrasonic tomographic velocimeter was capable of visualizing both symmetric and asymmetric axial flow fields with high reliability.     

亲子乐园空调送风方式的数值模拟研究

大型综合室内亲子乐园属于高大空间,设有游乐设施和游戏的特殊性使得对空间的舒适性要求一致,但是送风气流遇阻严重,室内存在较多气流死角,影响室内空气质量和儿童健康。因此其空调设计不仅需要考虑温度、风速的空间均匀度,还要考虑各点的空气龄和PMV-PPD指标。以天津某亲子乐园为研究对象,利用scSTREAM软件对适用于该房间的辐射供冷加新风、置换通风、混合通风三种空调方式的送风效果进行数值模拟分析,从流场的均匀性、人员的热舒适性等方面对模拟结果进行探讨,研究结果表明辐射供冷加新风方式的空间均匀性和PMV指标最佳,混合通风方式的空气龄最小。     

High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.     

THE effect of Srandom DOPANT fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel.     

田赛距离测量中全站仪的设计与实现

本文提出了将智能全站仪这种精密测量仪器广泛应用于田赛项目测量中，并结合其他科技元素用于解决田赛项目中跳远、投掷等项目的测量及数据管理问题，实现实时、自动、准确地裁定和报告比赛成绩。     

川北某黑色页岩型铼矿工艺矿物学研究

通过矿相显微镜、扫描电镜、电子探针、X射线能谱元素面分析等多种手段综合研究了川北某黑色页岩型铼矿中铼的赋存状态。样品为黑色页岩,有机碳含量较高。粘土矿物总量为14.6%,黄铁矿含量16.2%,石英含量37.7%。样品具典型的粘土结构,矿物粒度微细。铼有两种赋存状态,一种呈类质同象形式赋存于黄铁矿内,另一种则以分散形式存在。典型黄铁矿测点Re平均含量为0.024%。黄铁矿是Re的重要载体矿物。建议通过浮选分离黄铁矿,从而实现Re的富集。      

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

非连续采空区矿柱力学分析的数值模拟

为探讨非连续采空区矿柱力学原理，通过FLAC3D数值模拟技术，对下向水平分层进路式胶结充填采矿法开采形成的非连续采空区中矿柱的受力状态进行了分析。研究表明，非连续采空区中矿柱所受的力主要为覆岩的自重应力，水平应力对其影响不大；随着埋深的增加矿柱承受的垂直方向的力近似呈直线增加；随着非连续采空区跨度的增加（进路数量增加），非连续采空区受垂直方向的应力逐渐由围岩两侧向矿柱中间过渡。